No rush and strictly according to the instructions, or how to get the print out of paper

Sometimes a situation arises in which you need to quickly and without a trace remove the print from the paper.

This task may seem overwhelming as the paint is deeply embedded in the fiber structure. However, you can cope with it.

Read about the means by which you will be able to print out of paper and not damage the document itself, read the article.

How to remove without a trace?

There are several ways to get printing off paper. This can be done with the help of available tools. These include:

1. Egg... It is used boiled. When the egg is ready, it is peeled and rolled several times over the seal. The product must be warm during processing.
2. Chlorine. Very little cleaning agent is required for the procedure. A cotton swab is moistened in bleach. With its help, the liquid is transferred to the seal.

   Under the influence of bleach, the pigment will fade. It remains to wait only for the complete drying of the composition. If it was not possible to cope with the task the first time, the procedure is repeated. The average time that will have to be spent is half an hour.

3. Sun rays and acetone... To make the print less visible, the document is laid out on a windowsill, illuminated by the sun. Ultraviolet light promotes the decomposition of the coloring pigment, which is why it will become paler every day. After 2 weeks, the area is treated with a cotton swab dipped in acetone.

   This will allow you to complete the work you have started. So that other inscriptions do not disappear from the document under the influence of sunlight, they must be protected by covering them with a cloth or thick cardboard.

4. Mixture of acids... To remove the seal, you can use the following recipe: 10 g of citric acid and 10 g of oxalic acid are dissolved in 100 ml of water. The resulting composition is processed the stamp several times. When the seal becomes barely noticeable, the area is wiped with a damp cotton swab. All that remains is to wait for the liquid to dry.
5. Hydroperite and water... For processing, 1 tablet of hydroperite is dissolved in cool distilled water. The composition is dotted onto the paper and left to act. The seal should dissolve. If necessary, the processing is repeated.
6. Hydrogen peroxide with soda... In 1 teaspoon of peroxide, you need to dissolve a small amount of soda (it is taken at the tip of a knife). The components are mixed and applied with a brush. The stamp is processed until it becomes invisible.
7. Glycerin and alcohol... The components are combined in equal proportions and heated slightly to keep the mixture liquid. Carefully apply the composition to the stamp, blotting it with a cotton swab. If there is a concern that glycerin will leave stains behind, it is replaced with soda.

What not to do and why?

Actions to avoid:

• you cannot rub the paper from side to side - the material is very thin, therefore active mechanical action will lead to its damage;
• you cannot process the document with gasoline or other fatty compounds - after their application, a stain will remain on the paper, which will be difficult to cope with;
• do not start reprocessing if the paper is not dry - applying liquid to a damp surface will cause it to get wet and deteriorate.

Helpful information

Recommendations for removing printing from documents:

1. Process the print from the edge to the center. Otherwise, the coloring pigment will be scattered to clean areas.
2. Before using the selected composition for the first time, you need to test it on an unnecessary sheet. For the experiment, it is advisable to choose a paper that is similar in structure to the original.
3. There are recipes in which it is recommended to use potassium permanganate. Use it with caution, as it can leave stains behind.
4. To apply the bleaching compound, you need to use a brush or cotton swab. It should not be poured onto paper.
5. To prevent excess liquid from spreading on the paper, you need to keep a napkin on hand. It must be placed under the document being processed.
6. You can speed up the drying process of paper and enhance the brightening effect with an iron. To do this, lay out a napkin on a wet area, which is ironed several times. You cannot press too hard so that the paper does not burn.

Related videos

How to remove stamps, seals, ink from paper, the video will tell you:

Conclusion

Removing printing from paper is easy if you use the right tools. You need to act according to the instructions, without rushing to get the desired result. Haste will damage the document.